1
Which OSPF component is identical in all routers in an OSPF area after convergence?

2
Which three statements describe features of the OSPF topology table? (Choose three.)

3
A router is participating in an OPSFv2 domain. What will always happen if the dead interval expires before the router receives a hello packet from an adjacent DROTHER OPSF router?

4
Which command will provide information specific to OSPFv3 routes in the routing table?

5
Which wildcard mask would be used to advertise the 192.168.5.96/27 network as part of an OSPF configuration?

6
A network administrator enters the command ipv6 router ospf 64 in global configuration mode. What is the result of this command?

7
Fill in the blank.

8
Fill in the blank.

9
Which command should be used to check the OSPF process ID, the router ID, networks the router is advertising, the neighbors the router is receiving updates from, and the default administrative distance?

10
Which OSPFv3 function works differently from OSPFv2?

11

Launch PT  –  Hide and Save PT
Open the PT Activity. Perform the tasks in the activity instructions and then complete the task.

What message is displayed on http://www.ciscoville.com?

The correct configuration on R1 is:
router ospf 10
network 192.168.2.0 0.0.0.255 area 0
network 10.0.10.0 0.0.0.3 area 0

The correct configuration on R2 is:
router ospf 10
network 10.0.10.0 0.0.0.3 area 0
network 10.0.10.4 0.0.0.3 area 0
network 172.16.5.0 0.0.0.255 area 0

12
Fill in the blank. Do not use abbreviations.

13. By order of precedence, match the selection of router ID for an OSFP-enabled router to the possible router ID options. (Not all options are used.)

14. Match the description to the term. (Not all options are used.)

15
Which three statements describe the similarities between OSPFv2 and OSPFv3? (Choose three.)

16
What is a function of OSPF hello packets?

17. Match the information to the command that is used to obtain the information. (Not all options are used.)

18
What are the two purposes of an OSPF router ID? (Choose two.)

19
Which command will verify that a router that is running OSPFv3 has formed an adjacency with other routers in its OSPF area?

20
Single area OSPFv3 has been enabled on a router via the ipv6 router ospf 20 command. Which command will enable this OSPFv3 process on an interface of that router?

21
When a network engineer is configuring OSPFv3 on a router, which command would the engineer issue immediately before configuring the router ID?

22
Which criterion is preferred by the router to choose a router ID?

23
Which OPSF packet contains the different types of link-state advertisements?

24
What does a Cisco router use automatically to create link-local addresses on serial interfaces when OSPFv3 is implemented?

25. A router is participating in an OSPFv2 domain. What will always happen if the dead interval expires before the router receives a hello packet from an adjacent DROTHER OSPF router?

26. What is the first criterion used by OSPF routers to elect a DR?

27. Which OSPFv3 function works differently from OSPFv2?

28. What is used to create the OSPF neighbor table?

29. What are two reasons that will prevent routers from forming an OSPFv2 adjacency? (Choose two.)

30. What command would be issued to determine if a routing protocol-initiated relationship has been made with an adjacent router?

31. Which three addresses could be used as the destination address for OSPFv3 messages? (Choose three.)

32. 

Refer to the exhibit. A network administrator issued the command show ip ospf interface on the router R2. What conclusion can be drawn?

33. What command would be used to determine if a routing protocol-initiated relationship had been made with an adjacent router?

34. What are two reasons that will prevent two routers from forming an OSPFv2 adjacency? (Choose two.)

35. Match the OSPF state with the order in which it occurs. (Not all options are used.)