CCNA 200-125 Exam Dumps Part 6 Simulator Online

How Eigrp for ipv6 configuration done? ( choose two)

Which command can you enter to display the operational status of the network ports on a router?

Which two statements about VTP are true? (Choose two.)

Refer to the exhibit.

CCNA 200-125 Exam q4

On R1 which routing protocol is in use on the route to 192.168.10.1?

Which two options are the best reasons to use an IPV4 private IP space?(choose two)

Which statement about recovering a password on a Cisco router is true?

If three devices are plugged into one port on a switch and two devices are plugged into a different port,
how many collision domains are on the switch?

What are three components that comprise the SNMP framework? (Choose three)

Which command is used to enable CHAP authentication whit PAP as the fallback method on a serial
interface?

What is the effect of using the service password-encryption command?

Refer to the exhibit.

CCNA 200-125 Exam q11

A frame on vlan 1on switch s1 is sent to switch s2 when the frame is received on vlan 2,what causes this behavior?

Refer to the exhibit.

CCNA 200-125 Exam q12

Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown?

Why will a switch never learn a broadcast address?

What can you change to select switch as root bridge?

Refer to exhibit.

CCNA 200-125 Exam q15

What Administrative distance has route to 192.168.10.1 ?

Which statement about IPv6 link-local addresses is true?

Which configuration can be used with PAT to allow multiple inside address to be translated to a single
outside address ?

Which two types of information are held in the MAC address table? (Choose two)

Which command can you enter to create a NAT pool of 6 addresses?

Which header field is new on IPv6?

Which value is used to determine the active router in an HSRP default configuration?

Which three are valid modes for a switch port used as a VLAN trunk? (choose three)

Which value must you configure on a device before EIGRP for IPv6 can start running?

Which type of attack can be mitigated by configuring the default native VLAN to be unused?

Which option describes a difference between EIGRP for IPv4 and IPv6?

Which option describes the purpose of traffic policing?

Which process is associated with spanning-tree convergence?

What is a difference between TACACS+ and RADIUS in AAA?

Which option is a benefit of switch stacking?

Which port state is introduced by Rapid-PVST?

What are the possible trunking modes for a switch port? (Choose three.)

Refer to the exhibit.

CCNA 200-125 Exam q32

When running OSPF, What would cause router A not to form an adjacency with router B?

What command instructs the device to timestamp Syslog debug messages in milliseconds?

Refer to the exhibit.

CCNA 200-125 Exam q34

What set of commands was configured on interface Fa0/3 to produce the given the output?

While troubleshooting a connection problem on a computer,you determined that the computer can ping a specific web server but it cannot connect to TCP port 80 on that server.Which reason for the problem is most likely ture?

When troubleshooting Ethernet connectivity issues,how can you verify that an IP address is known to a router?

Refer to the exhibit.

CCNA 200-125 Exam q37

After you apply the given configuration to R1, you determine that it is failing to advertise the 172.16.10.32/27 network .Which action most likely to correct the problem.

Which two steps must you perform on each device that is configured for IPv4 routing before you implement OSPFv3?(Choose two)

Which option is the main function of congestion management?

Which command must you enter to enable OSPFV2 in an IPV4 network?

Refer to the exhibit.

CCNA 200-125 Exam q41

If RTR01 is configured as shown,which three addresses will be received by other routers that are running EIGRP on the network?(choose three)

Which type of secure MAC address must be configured manually?

Which two options are fields in an Ethernet frame?(choose two)

Where does a switch maintain DHCP snooping information ?

To enable router on a router subinterface,which two steps must you perform?(choose two)

Which command can you enter on a switch to determine the current SNMP security model?

Which statement about spanning-tree root-bridge election is true?

Which two statements about IPv6 address 2002:ab10:beef::/48 are true?(choose two)

Which step in the router boot process searches for an IOS image to load into the router?

Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

Which three statements about DWDM are true? (Choose three)

If two OSPF neighbors have formed complete adjacency and are exchanging link-state advertisements, which state have they reached?

Which tunneling mechanism embeds an IPv4 address within an IPv6 address?

Which of the following statements describe the network shown in the graphic? (Choose two.)

CCNA 200-125 Exam q54

Which one of these is a valid HSRP Virtual Mac Address?

Assuming the default switch configuration which vlan range can be added modified and removed on a cisco switch?

Refer to the exhibit.

CCNA 200-125 Exam q57

Which two statements are true of the interfaces on switch1?(choose two)

Refer to the exhibit.

CCNA 200-125 Exam q58

How should the FastEthernet0/1 port on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?

Which three statements about the features of SNMPv2 and SNMPv3 are true? (Choose three.)

Which command do use we to see SNMP version?

Which protocol does ipv6 use to discover other ipv6 nodes on the same segment?

What is the most efficient subnet mask for a point to point ipv6 connection?

What are three features of the IPV6 protocol?(choose three)

Why do large OSPF networks use a hierarchical design?(choose three)

Where does routing occur within the DoD TCP/IP reference model?

Refer to Exhibit.

CCNA 200-125 Exam q66

If Computer A is sending traffic to computer B, which option is the source ip address when a packet leaves R1 on interface F0/1?

Which feature can you use to restrict SNMP queries to a specific OID tree?

Refer to the exhibit.

CCNA 200-125 Exam q68

After you apply the give configurations to R1 and R2 you notice that OSPFv3 fails to start Which reason for the problem is most likely true ?

Refer to the exhibit.

CCNA 200-125 Exam q69

After you apply the given configuration to a router, the DHCP clients behind the device cannot communicate with hosts outside of their subnet. Which action is most likely to correct the problem?

Which command can you enter in a network switch configuration so that learned mac addresses are saved in configuration as they connect?